Under Uspeed WIFI Repeater Access Point 300/150/54 Mbit and Range Extender for 802.11 b/g/n standar

22 Aug

Customer Video Review Length:: 6:03 Minsgreat product’my experience, if you have any problem installing with cabel, be sure to change the ip adress fixed to 192.168.10.1, your computer’s ip adress must to be 192.168.10.X’2~255)
Ordered three of these for work. Local Best Homosexual Dating . Followed the instructions provided and had had all three up and running in less than 30 minutes. There were areas that I could not even get a signal before I installed these repeaters, now I have coverage in the entire 33,000 square foot facility. You can’t beat the price or the product. I highly recommend.
This product does exactly what it says. I had the Uspeed wifi repeater and the little manual that came with it ready for action. Following the steps went smoothly. It recognized my wireless signal and began repeating it without further issues. It is important to remember to do the following things: (1) the computer that you will be using to work on the repeater must have a static ip according to the manual, if you don’t do this, you won’t have access to the repeater. Buy Best Estee Lauder Women Fragrances Reviews . (2) Once you followed the steps and the repeater has a working signal, be sure to go back into the repeater’s interface and change it’s wireless signal settings. Here you can change the name of the singal amongst other things. I named my singal 2 and the access point 1. Overall, I’m very satisfied.

The Wifi Repeater is mainly used to achieve two goals in optimizing the network environment: one is repeating the signal, the other being repeating the original coverage of the signal. Eliminate wireless “dead zones” and repeat signals where you want!

Two Modes
Wireless Access Point Mode – This standard mode creates a wireless network from your router or DSL modem so that you can connect the web wirelessly and seamlessly.
Wireless Repeater Mode ( or Range Extender ) – This mode boosts the coverage of your existing wireless network by detecting the signal and repeating it to a further range.

Package include
1 pc Wireless-N WIFI Repeater; 1 pc RJ-45 cable; 1 pc instruction manual

Using Tip
Under most circumstances, the Wifi Repeater fails to connect to internet because of IP address issue. The IP address for Wifi Repeater is fixed to 192.168.10.1, please set the IP address of your computer/laptop manually as 192.168.10.X. Local Buy Best Price For Fossil Watch Cases . (X representing a number from 2-225)

Note
- The WLAN client must support at least the WPA encryption standard
- The network name (SSID) of the WLAN access point must be set to “visible”
- Never interrupt the upgrade procedure by closing the web browser or physically disconnect your computer from router. By doing this, you may have to return this router to the dealer (Warranty voids if you interrupted the upgrade procedure)Customer Video Review Length:: 6:03 Minsgreat product’my experience, if you have any problem installing with cabel, be sure to change the ip adress fixed to 192.168.10.1, your computer’s ip adress must to be 192.168.10.X’2~255)
Ordered three of these for work. Followed the instructions provided and had had all three up and running in less than 30 minutes. There were areas that I could not even get a signal before I installed these repeaters, now I have coverage in the entire 33,000 square foot facility. You can’t beat the price or the product. I highly recommend.
This product does exactly what it says. I had the Uspeed wifi repeater and the little manual that came with it ready for action. Following the steps went smoothly. It recognized my wireless signal and began repeating it without further issues. It is important to remember to do the following things: (1) the computer that you will be using to work on the repeater must have a static ip according to the manual, if you don’t do this, you won’t have access to the repeater. (2) Once you followed the steps and the repeater has a working signal, be sure to go back into the repeater’s interface and change it’s wireless signal settings. Here you can change the name of the singal amongst other things. I named my singal 2 and the access point 1. Overall, I’m very satisfied.

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

Follow

Get every new post delivered to your Inbox.

%d bloggers like this: